Can I Install a Bathtub Myself? Factors to Consider And Actions
Can I Install a Bathtub Myself? Factors to Consider And Actions
Blog Article
How do you actually feel in regards to A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't precisely rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the task can relocate easily; if you need to open up a wall surface to eliminate the old bathtub as well as position the new bathtub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub as well as set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is much better to think about employing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This short article will aid you mount a brand-new bathtub in your bathroom if you have actually already acquired a brand-new bathtub and do not require to alter the plan of your previous water supply pipelines.
Your devices and product checklist ought to consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the limited access that is commonly the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous kind ought to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the required position. The wood boards are handy in equally spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub up until the level reviews level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the water system as well as examine all joints as well as brand-new pipework for leakages as well as tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub must wait till the bath tub has been utilized at least when as this will certainly resolve it right into its last placement.
Planning for the Setup
To start with, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can fracture fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our topic on How to Install a Bathtub Yourself. Thanks so much for spending some time to read through our short article. Sharing is good. Who knows, you might be helping someone out. I praise you for your time. Please come by our blog back soon.
Get A Free Estimate
Report this page